refrigerator water dispenser not working after replacing filter

This could take several minutes. A kink in the line can reduce water flow.

Refrigerator Water Dispenser Not Working After Filter Change

Straighten the water source line to restore adequate water flow and pressure.

. Flush about a gallon out or until the water pressure is back to normal. With the water line still disconnected and the power still off locate the valves solenoid coils. Start crossing things off your list today.

To help reduce the chances of a pinched water line do not push the refrigerator too. If water does flow now insert the new filter again. If it isnt it may need to be replaced.

Water-tube may be frozen- to confirm this disconnect the tube at the bottom of the door and blow air through it. When installed improperly you simply should go back and try the installation again. Remove the water supply tube and try to blow air through it to see if air is able to pass through it.

This does not apply to Top Freezer refrigerators since they dont have. Remove the refrigerators control board cover to locate the micro switch. If water still wont flow the filter housing W10121140 will probably need to be replaced.

Experiencing low or no ice. Air may be trapped in the water system after replacing the filter. Ad Free price estimates for Repairmen.

Disconnect the two wires from the terminals located on the coil. You can replace the filter housing for about 170 or do a poor mans repair. Other causes of a broken refrigerator water dispenser.

Refrigerator water dispenser not working. When you changed the filter and put the new one in the one or both of the valve stems broke off. Hold a glass under dispenser until the water starts flowing.

Asking a tech to fix a broken refrigerator dispenser seems like an obvious solution but a common unprofessional repair is often just masking the problem instead of actually solving it. It took a few tries to get all of the air out of the system. But it does vary by model.

Water inlet valves require a minimum of 20 psi to function properly. If your GE refrigerator wont dispense water after the filter has been replaced it could be that the water supply tube in the door is frozen. Ad 19 Million Parts - Ships Same Day.

Check to make sure there are no kinks in the water supply line. If only the dispenser fails to work now and you can hear the water valve getting energized it will indicate the valve is not opening. Shop Water Filters - Purchase a GE Appliance part online.

If the water dispenser is not working the water pressure from the house might be too low. Unplugged your refrigerator and disconnect the water supply. Otherwise replace the micro switch.

Problematic Dispenser Control Board. It must show a reading of 200-500 ohms. After replacing the water filter then you must flush the air out of the lines.

Perhaps the best bet is to start from scratch with your installation. I took out the filter dumped out the water out of the filter refilled the filter in the sink and reinstalled the filter. If the refrigerator water dispenser is not working the water filter might be clogged.

Here are a few things you can check if youre experiencing issues with your refrigerator water filter. A good check for this will be to make the check in the information you have received. Refrigerator water dispenser not working after filter change.

Check the water tank behind the vegetable bins to see if it is frozen or cracked. Use a multimeter to test the solenoid and see if it is running electricity steadily. Use multi-meter to test switchs continuity.

The air may be preventing the dispenser from working due. Check if Water Filter is Restricting Water Flow to Dispenser The water filter can be clogged due to micro particles in the water. Browse Order Now.

I looked where my filter goes in and saw that the outside valve stem was slightly shorter than the inside one. Connect with a Repairman instantly. A common DIY fix is as follows clean condenser coils and fan motor filters replace defrost thermostat and pressure.

A clogged water filter can also cause problems like reduced water pressure. Make sure the water supply is properly connected to a cold water supply and the water shutoff valve is fully opened. Over time the water filter becomes clogged rendering it inefficient and limits water flow through the dispenser.

The water filter can be located in a small compartment that is easy to access. If your Frigidaire refrigerator wont dispense water or ice and you have not changed the water filter in over 6 months it is past due for a change. When you install a new filter its full of air.

Press the dispenser cradle for at least 5 minutes to purge any air from the water lines. The water filter is a small component that can be cleaned or replaced quite easily. Kitchenaid Refrigerator Water Dispenser not Working After Replacing Filter Several reasons may make your dispenser stop working apart from the water filter.

Change the filter using a factory authorized brand filter. If you have replaced the filter and water is still not dispensing read below to find the solution. Try changing the water filter.

Improperly installing your water filter can lead to issues with water flow. You should experience an increase in water flow. If the refrigerator water dispenser worked before you changed out the filter go back and re-traced your steps.

Free estimates no guessing. If air fails to pass through it means the line is frozen. Generally it is behind the actuator.

Share Improve this answer answered Oct 5 2014 at 2352 Dave 31 2 Add a comment 1 Yes air will have that effect. Kenmore Refrigerator Water Dispenser Not Working After Replacing Water Filter Solved Try running a few gallons of water out of the waterline in order to clear any air trapped in the system.

Why Is My Fridge Water Dispenser Not Working Family Handyman